{"id":486204,"date":"2024-11-05T12:13:02","date_gmt":"2024-11-05T12:13:02","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/agma-2008-d11\/"},"modified":"2024-11-05T12:13:02","modified_gmt":"2024-11-05T12:13:02","slug":"agma-2008-d11","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/agma\/agma-2008-d11\/","title":{"rendered":"AGMA 2008-D11"},"content":{"rendered":"<p>\n<u><strong>SCOPE<\/strong><\/u><\/p>\n<p>\tThis standard applies to the assembly of all bevel gears.<\/p>\n<p>\tThe term <em>bevel<\/em> gears is used to mean straight, spiral, and hypoid gear designs. If data pertain to one or more but not all, the specific forms are identified.<\/p>\n<p>\tThe standard provides the following:<\/p>\n<ul>\n<li>\n<p>\t\tA better understanding of the need for correct positioning of bevel gears.<\/li>\n<li>\n<p>\t\tInformation necessary for correct assembly and positioning of bevel gears in their respective housings.<\/li>\n<li>\n<p>\t\tInformation for methods personnel in establishing detailed assembly procedures for specific applications.<\/li>\n<li>\n<p>\t\tInformation for tooling personnel responsible for equipping an assembly department with the tools and gages necessary for proper assembly.<\/li>\n<li>\n<p>\t\tInstruction to assembly personnel for obtaining tooth contact patterns, for interpreting the tooth contact patterns, and for adjusting the position of the members to change the tooth contact patterns.<\/li>\n<\/ul>\n<p>\tThis standard applies to the assembly of all bevel gears. While certain design considerations and development techniques are mentioned to clarify different aspects, this standard is not intended as a design guide.\u00a0 It is prepared on the assumption that gears and mountings are designed in accordance with ANSI\/AGMA 2005-D03, <em>Design Manual for Bevel Gears<\/em>.<\/p>\n<p>\n<u><strong>FOREWORD<\/strong><\/u><\/p>\n<p>\t[The foreword, footnotes and annexes, if any, in this document are provided for informational purposes only and are not to be construed as a part of ANSI\/AGMA Standard 2008-D11, <em>Assembling Bevel Gears<\/em>.]<\/p>\n<p>\tInformation pertaining to recommended practice in the assembling of bevel gears is not new in the published literature of the American Gear Manufacturers Association.\u00a0 In 1927, the <em>Recommended Practice of the American Gear Manufacturers Association of Adjustment of Bevel Gears in Assembly<\/em> was adopted and published.<\/p>\n<p>\tThis practice was revised in 1940 by the Bevel Gear Committee, but no further revision was undertaken until 1967.<\/p>\n<p>\tSince the satisfactory performance of bevel gears is closely related to proper installation, it was decided by the Bevel Gearing Committee that it was important to maintain information on this subject in the literature of the Association.<\/p>\n<p>\tThis manual brings up to date and reflects the present thinking on the information given in the original practice.<\/p>\n<p>\tThis manual was prepared for the assembly personnel in the factory and for the service personnel in the field.\u00a0 Each definition, explanation, and instruction is directed toward the physical appearance of the gears as they are inspected and assembled.\u00a0 The definitions are simple.\u00a0 The explanations are thorough.<\/p>\n<p>\tEach section devoted to the tooth contact pattern of a particular type of gear is intended to be complete in itself for use as a separate shop manual if desired.\u00a0 For this reason, when the manual is read in its entirety, these sections seem repetitious.<\/p>\n<p>\tIn contrast, the sections devoted to angular gears are brief and general.\u00a0 The committee concluded that each angular configuration requires separate treatment, and that a complete coverage of all of the possible combinations would be impractical if at all possible.<\/p>\n<p>\tThe first draft of AGMA 331.01 was prepared by the Bevel Gearing Committee in October, 1967.\u00a0 It was approved by the AGMA membership and became an official AGMA manual as of August 2. 1969.\u00a0 The manual was reaffirmed in 1976.<\/p>\n<p>\tANSI\/AGMA 2008-B90 is a revision of AGMA 331.01.\u00a0 It was approved by the AGMA membership on November 10, 1989, and as an American National Standard on May 4, 1990.<\/p>\n<p>\tAn errata was issued in June, 1995 that changed the denominator of the equation for &#034;Transverse Backlash, <em>B<\/em><sub>t<\/sub>\u201d in figure 7-1, to reflect the product of the cosine terms, rather than their difference.<\/p>\n<p>\tANSI\/AGMA 2008-C01 was a correction of ANSI\/AGMA 2008-B90.\u00a0 In 2000 an errata revision of clauses 7.2, 8.3.1 and 8.3.2 was balloted.\u00a0 This was approved by the AGMA membership in June 2001 and as an American National Standard on November 20, 2001.<\/p>\n<p>\tANSI\/AGMA 2008-D11 is an update to ANSI\/AGMA 2008-C01, converting to metric.\u00a0 Backlash recommendations were revised to reflect current accuracy standards.\u00a0 An Annex was added to detail the procedures used in contact pattern checking.<\/p>\n<p>\tThe first draft of ANSI\/AGMA 2008-D11 was made in April, 2008.\u00a0 It was approved by the AGMA membership in April, 2011.\u00a0 It was approved as an American National Standard on August 29, 2011.<\/p>\n","protected":false},"excerpt":{"rendered":"<p><b>Assembling Bevel Gears<\/b><\/p>\n<table style=\"width: 100%\" border=\"0\" cellspacing=\"0\" cellpadding=\"0\">\n<tbody>\n<tr>\n<td>Published By<\/td>\n<td>Publication Date<\/td>\n<td>Number of Pages<\/td>\n<\/tr>\n<tr>\n<td><a href=\"https:\/\/pdfstandards.shop\/product-category\/publishers\/agma\/\"><b>AGMA<\/b><\/a><\/td>\n<td>2011<\/td>\n<td>49<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":486213,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[2659],"product_tag":[],"class_list":{"0":"post-486204","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-agma","8":"first","9":"instock","10":"sold-individually","11":"shipping-taxable","12":"purchasable","13":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/486204","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/486213"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=486204"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=486204"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=486204"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}