BS ISO 4586-2:2018
$215.11
High-pressure decorative laminates (HPL, HPDL). Sheets based on thermosetting resins (usually called laminates) – Determination of properties
| Published By | Publication Date | Number of Pages |
| BSI | 2018 | 114 |
This document specifies the methods of test for determination of the properties of high-pressure decorative laminates (HPL, HPDL) as defined in Clause 3. These methods are primarily intended for testing the sheets specified from ISO 4586‑3 to ISO 4586‑8.
The precision of the test methods specified in Clauses 5, 6, 7, 8, 9, 10, 13, 14, 16, 19, 20, 21, 22, 24, 25, 26, 39, and 40 is not known because interlaboratory data are not available. When interlaboratory data are obtained, precision statements will be added to the test methods at the following revision. As all the other test methods have an end point determination based on subjective judgement, it is not meaningful to make a statement of precision in these cases.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | National foreword |
| 11 | Foreword |
| 12 | Introduction |
| 13 | 1 Scope 2 Normative references |
| 14 | 3 Terms and definitions 4 Assessment of appearance 4.1 Principle |
| 15 | 4.2 Apparatus 4.3 Test specimen 4.4 Procedure 4.5 Test report 5 Determination of thickness 5.1 Principle 5.2 Apparatus |
| 16 | 5.3 Test specimen 5.4 Procedure 5.5 Test report 6 Determination of length and width 6.1 Principle 6.2 Apparatus 6.3 Test specimen 6.4 Procedure 6.5 Expression of results 6.6 Test report |
| 17 | 7 Determination of edge straightness 7.1 Principle 7.2 Apparatus 7.3 Test specimen 7.4 Procedure 7.5 Expression of results 7.6 Test report |
| 18 | 8 Determination of edge squareness (Method A) 8.1 Principle 8.2 Apparatus 8.3 Test specimen 8.4 Procedure |
| 19 | 8.5 Expression of results 8.6 Test report 9 Determination of edge squareness (Method B) 9.1 Principle 9.2 Apparatus 9.3 Test specimen |
| 20 | 9.4 Procedure 9.5 Expression of results 9.6 Test report 10 Determination of flatness 10.1 Principle 10.2 Apparatus |
| 21 | 10.3 Test specimens 10.4 Procedure 10.5 Expression of results |
| 22 | 10.6 Test report 11 Resistance to surface wear 11.1 Principle 11.2 Materials 11.2.2 Abrasive paper strips 11.3 Apparatus |
| 23 | 11.4 Test specimens 11.5 Preparation of specimens and abrasive paper 11.6 Procedure 11.6.1 Preparation of abrasive wheels 11.6.2 Calibration of abrasive paper 11.6.3 Abrasion of specimen |
| 24 | 11.7 Expression of results 11.8 Test report |
| 25 | 12 Resistance to abrasion (Flooring grade laminates) 12.1 Principle 12.2 Materials 12.3 Apparatus 12.4 Test specimens 12.5 Preparation of specimens and abrasive paper |
| 26 | 12.6 Procedure 12.6.1 Preparation of abrasive wheels 12.6.2 Calibration of abrasive paper 12.6.3 Abrasion of specimen |
| 27 | 12.7 Expression of results 12.8 Test report 13 Resistance to immersion in boiling water 13.1 Principle 13.2 Apparatus 13.3 Test specimens |
| 28 | 13.4 Procedure 13.5 Expression of results |
| 29 | 13.6 Test report 14 Substrate protection against water vapour 14.1 Principle 14.2 Apparatus |
| 30 | 14.3 Test specimens 14.4 Procedure 14.5 Expression of results |
| 31 | 14.6 Test report 15 Resistance to water vapour 15.1 Principle 15.2 Apparatus 15.3 Test specimen 15.4 Procedure |
| 32 | 15.5 Expression of results |
| 33 | 15.6 Test report 16 Resistance to wet conditions (Exterior grade laminates) 16.1 Principle 16.2 Apparatus 16.3 Test specimens 16.4 Procedure |
| 34 | 16.5 Expression of results 16.6 Test report |
| 35 | 17 Resistance to dry heat (Method A) 17.1 Principle 17.2 Apparatus and materials |
| 36 | 17.3 Test specimen 17.4 Test procedure |
| 37 | 17.5 Examination of the test specimen 17.6 Expression of results 17.7 Test report |
| 38 | 18 Resistance to dry heat (Method B) 18.1 Principle 18.2 Materials 18.3 Apparatus 18.4 Test specimen |
| 39 | 18.5 Procedure 18.6 Expression of results |
| 41 | 18.7 Test report 19 Dimensional stability at elevated temperature (Method A) 19.1 Principle 19.2 Apparatus 19.3 Test specimens |
| 42 | 19.4 Procedure 19.4.2 Dry-heat test 19.4.3 High-humidity test 19.5 Expression of results 19.6 Test report 20 Dimensional stability at elevated temperature (Method B) 20.1 Principle 20.2 Apparatus |
| 44 | 20.3 Test specimens 20.4 Procedure 20.4.1 General 20.4.2 Dry-heat test 20.4.3 High-humidity test 20.5 Expression of results |
| 45 | 20.6 Test report 21 Dimensional stability at ambient temperature (Method A) 21.1 Principle 21.2 Apparatus |
| 46 | 21.3 Test specimens 21.4 Procedure 21.5 Expression of results 21.6 Test report |
| 47 | 22 Dimensional stability at ambient temperature (Method B) 22.1 Principle 22.2 Apparatus 22.3 Test specimens 22.4 Procedure |
| 48 | 22.5 Expression of results 22.6 Test report 23 Resistance to climatic shock (exterior grade laminates) 23.1 Principle 23.2 Apparatus |
| 49 | 23.3 Test specimens 23.4 Procedure |
| 50 | 23.5 Expression of results 23.6 Test report 24 Resistance to impact by small diameter ball 24.1 Principle 24.2 Materials |
| 51 | 24.3 Apparatus |
| 52 | 24.4 Test specimens 24.5 Calibration of the impact tester |
| 54 | 24.6 Procedure 24.7 Expression of results |
| 55 | 24.8 Test report 25 Resistance to impact by large diameter ball 25.1 Principle 25.2 Materials 25.3 Apparatus |
| 58 | 25.4 Test specimens 25.5 Procedure 25.6 Expression of results 25.7 Test report |
| 59 | 26 Resistance to impact by large diameter ball (Flooring grade laminates) 26.1 Principle 26.2 Materials 26.3 Apparatus 26.4 Test specimens 26.5 Procedure |
| 60 | 26.6 Expression of results 26.7 Test report 27 Resistance to cracking under stress (Laminates ≤ 2 mm thick) 27.1 Principle 27.2 Apparatus |
| 62 | 27.3 Test specimens 27.4 Procedure |
| 63 | 27.5 Expression of results 27.6 Test report |
| 64 | 28 Resistance to crazing (Compact laminates) 28.1 Principle 28.2 Apparatus 28.3 Test specimens |
| 65 | 28.4 Procedure 28.5 Expression of results 28.6 Test report 29 Resistance to scratching 29.1 Principle 29.2 Materials |
| 66 | 29.3 Apparatus 29.4 Calibration of apparatus |
| 68 | 29.5 Test specimen |
| 69 | 29.6 Procedure |
| 70 | 29.7 Expression of results 29.8 Test report |
| 72 | 30 Resistance to staining (Method A) 30.1 Principle 30.2 Staining agents |
| 73 | 30.3 Materials 30.4 Apparatus |
| 74 | 30.5 Test specimens 30.6 Procedure 30.7 Expression of results 30.8 Test report |
| 75 | 31 Resistance to staining (Method B) 31.1 Principle 31.2 Materials |
| 76 | 31.3 Apparatus 31.4 Test specimens 31.5 Procedure |
| 77 | 31.6 Expression of results |
| 78 | 31.7 Test report 32 Lightfastness (xenon arc) (Method A) 32.1 Principle 32.2 Apparatus |
| 79 | 32.3 Test specimen 32.4 Procedure 32.5 Assessment and expression of results 32.6 Test report |
| 80 | 33 Lightfastness (xenon arc) (Method B) 33.1 Principle 33.2 Apparatus 33.3 Test specimen |
| 81 | 33.4 Procedure 33.5 Expression of results |
| 82 | 33.6 Test report 34 Resistance to UV light (Exterior grade laminates) 34.1 Principle 34.2 Apparatus 34.3 Test specimens 34.4 Procedure |
| 83 | 34.5 Evaluation and expression of results 34.5.1 Contrast 34.5.2 Appearance 34.6 Test report |
| 84 | 35 Resistance to artificial weathering (Exterior grade laminates) 35.1 Principle 35.2 Apparatus 35.3 Test specimens 35.4 Procedure |
| 85 | 35.5 Examination and expression of results 35.5.1 General 35.5.2 Contrast 35.5.3 Appearance 35.6 Test report |
| 86 | 36 Resistance to radiant heat 36.1 Principle 36.2 Apparatus 36.3 Test specimen |
| 88 | 36.4 Procedure 36.5 Test report 37 Formability (Method A) 37.1 Principle |
| 89 | 37.2 Apparatus 37.3 Test specimens 37.4 Procedure 37.4.1 General |
| 90 | 37.4.2 Calibration of test apparatus |
| 91 | 37.4.3 Test procedure |
| 92 | 37.5 Test report 38 Formability (Method B) 38.1 Principle 38.2 Apparatus |
| 93 | 38.3 Test specimens 38.4 Procedure 38.4.1 Calibration of test apparatus 38.4.2 Test procedure |
| 100 | 38.5 Test report 39 Resistance to blistering (Method A) 39.1 Principle 39.2 Apparatus 39.3 Test specimens 39.4 Procedure 39.4.1 Calibration of test apparatus 39.4.2 Test procedure |
| 101 | 39.5 Test report 40 Resistance to blistering (Method B) 40.1 Principle 40.2 Apparatus |
| 102 | 40.3 Test specimens 40.4 Procedure 40.5 Test procedure 40.6 Test report 41 Resistance to wet heat (100 °C) 41.1 Principle 41.2 Apparatus |
| 103 | 41.3 Test specimen 41.4 Procedure |
| 104 | 41.5 Expression of results |
| 105 | 41.6 Test report 42 Determination of microscratch resistance 42.1 Principle 42.2 Apparatus |
| 106 | 42.3 Materials |
| 107 | 42.4 Calibration 42.4.1 Assembly and maintenance of the Martindale tester 42.4.2 Method for checking the Lissajous figure |
| 108 | 42.5 Test specimens 42.5.1 Preparation 42.5.2 Test surface 42.6 Procedure 42.6.1 General |
| 109 | 42.6.2 Method |
| 110 | 42.7 Classification of the image after testing to procedure B 42.8 Test report |
| 112 | Bibliography |
