BS ISO 13044-2:2013
$167.15
Road vehicles. Fully automatic coupling systems 24 V (FACS) for heavy commercial vehicle combinations – 50 mm fifth wheel couplings. Electrical and pneumatic interface
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 36 |
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Introduction |
| 8 | Section sec_1 Section sec_2 1 Scope 2 Normative references |
| 9 | Section sec_3 Section sec_3.1 Section sec_3.2 Section sec_3.2.1 Section sec_3.2.2 Section sec_3.2.3 Section sec_3.2.4 Section sec_4 Section sec_4.1 3 Terms and definitions 4 Requirements 4.1 General |
| 10 | Section sec_4.2 Section sec_4.3 Section sec_4.4 Section sec_4.4.1 Section sec_4.4.2 Section sec_4.5 4.2 Tractor and semi-trailer 4.3 Mechanical interface, Manual operation 4.4 EPI module 4.5 Mating of the two EPI parts |
| 11 | Section sec_4.6 Section sec_4.6.1 Table tab_a Figure fig_1 4.6 Guiding and alignment |
| 12 | Table tab_b Figure fig_2 Section sec_4.6.2 Section sec_4.6.2.1 Section sec_4.6.2.1.1 Section sec_4.6.2.1.2 Section sec_4.6.2.2 Section sec_4.6.2.3 Section sec_4.6.2.4 Section sec_4.6.2.5 Section sec_4.6.2.6 Section sec_4.6.3 Section sec_4.6.3.1 Section sec_4.6.3.2 Section sec_4.6.3.3 Section sec_4.6.3.4 |
| 13 | Section sec_4.6.3.5 Section sec_4.6.3.6 Section sec_4.6.4 Section sec_4.6.5 Section sec_4.7 Section sec_4.7.1 Section sec_4.7.1.1 Section sec_4.7.1.2 Section sec_4.7.2 Section sec_4.7.3 4.7 Encapsulation and protection |
| 14 | Section sec_4.8 Section sec_4.9 Section sec_4.10 Section sec_5 Section sec_5.1 4.8 Automation of landing legs 4.9 ISO 11992 Cable length 4.10 Mixed mode operation 5 Tests and specific requirements 5.1 General |
| 15 | Table tab_1 Section sec_5.2 Section sec_5.3 Section sec_5.4 5.2 Visual examination 5.3 Dimensional check 5.4 Connection and disconnection |
| 16 | Section sec_5.5 Section sec_5.5.1 Section sec_5.5.2 Section sec_5.6 Section sec_5.7 Table tab_c Figure fig_3 5.5 Locking device operation 5.6 Current carrying capacity 5.7 Connection resistance (voltage drop), cable capacitance and pneumatics |
| 17 | Figure fig_3___1 Table tab_d Figure fig_4 Figure fig_4___1 |
| 18 | Section sec_5.8 Section sec_5.9 Section sec_5.10 Section sec_5.11 Section sec_5.12 Section sec_5.13 Figure fig_5 Section sec_5.14 Section sec_5.15 5.8 Current cycling 5.9 Withstand voltage 5.10 Influence of water 5.11 Protection against dust 5.12 Endurance 5.13 Vibration 5.14 Shock resistance 5.15 Drop test |
| 19 | Section sec_5.16 Section sec_5.17 Section sec_5.18 Section sec_5.19 Section sec_5.20 5.16 Temperature/humidity cycling 5.17 Salt spray 5.18 Chemical resistance 5.19 Leakage test of pneumatic connections 5.20 Functional test of protection covers |
| 20 | Annex sec_A Annex sec_A.1 Table tab_e Figure fig_A.1 Annex A (normative) EPI module — Dimensional characteristics |
| 21 | Annex sec_A.2 Table tab_f Figure fig_A.2 |
| 22 | Table tab_g Figure fig_A.3 Annex sec_A.3 Annex sec_A.3.1 Table tab_h |
| 23 | Figure fig_A.4 |
| 24 | Annex sec_A.3.2 |
| 25 | Table tab_i Figure fig_A.5 |
| 26 | Table tab_j Figure fig_A.6 Figure fig_A.7 Figure fig_A.8 |
| 27 | Table tab_k Figure fig_A.9 |
| 28 | Annex sec_B Table tab_l Figure fig_B.1 Table tab_B.1 Annex B (normative) EPI module — Contact allocation |
| 30 | Annex sec_C Annex sec_C.1 Annex sec_C.1.1 Annex sec_C.1.2 Annex sec_C.1.3 Annex sec_C.1.4 Annex C (normative) Mixed mode operation |
| 31 | Table tab_m Figure fig_C.1 |
| 32 | Table tab_n Figure fig_C.2 Table tab_o Figure fig_C.3 |
| 33 | Table tab_p Figure fig_C.4 Table tab_q Figure fig_C.5 |
| 34 | Reference ref_1 Reference ref_2 Reference ref_3 Bibliography |
