🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN IEC 60086-1:2021:2022 Edition

BS EN IEC 60086-1:2021:2022 Edition

$198.66

Primary batteries – General

Published By Publication Date Number of Pages
BSI 2022 54
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

PDF Catalog

PDF Pages PDF Title
2 undefined
6 Blank Page
7 English
CONTENTS
10 FOREWORD
12 INTRODUCTION
13 1 Scope
2 Normative references
3 Terms and definitions
16 4 Requirements
4.1 General
4.1.1 Design
4.1.2 Battery dimensions
4.1.3 Terminals
18 4.1.4 Classification (electrochemical system)
Tables
Table 1 – Standardized electrochemical systems
19 4.1.5 Designation
4.1.6 Marking
20 4.1.7 Interchangeability: battery voltage
Table 2 – Marking requirements
21 4.2 Performance
4.2.1 Discharge performance
4.2.2 Dimensional stability
4.2.3 Leakage
4.2.4 Open-circuit voltage limits
4.2.5 Service output
4.2.6 Safety
22 4.2.7 Validity of testing
5 Performance – Testing
5.1 Capacity testing versus application and service output testing
5.2 Discharge testing
5.2.1 General
23 5.2.2 Application tests
5.2.3 Service output tests
24 5.3 Conformance check to a specified minimum average duration
5.4 Guidance for considering proposed value of minimum average duration
5.5 OCV testing
5.6 Insulation resistance
5.7 Battery dimensions
5.8 Leakage and deformation
25 6 Performance – Test conditions
6.1 Storage and discharge conditions
6.2 Commencement of discharge tests after storage
6.3 Discharge test conditions
6.3.1 General
6.3.2 Compliance
Table 3 – Conditions for storage before and during discharge testing
26 6.4 Load resistance
6.5 Time periods
6.6 Test condition tolerances
6.7 Activation of ‘P’-system batteries
Table 4 – Resistive loads for tests
Table 5 – Time periods for tests
Table 6 – Test condition tolerances
27 6.8 Measuring equipment
6.8.1 Voltage measurement
6.8.2 Mechanical measurement
7 Sampling and quality assurance
8 Battery packaging
28 Annexes
Annex A (normative) Criteria for the standardization of batteries
Table A.1 – Items necessary to standardize
29 Annex B (informative) Recommendations for equipment design
B.1 Technical liaison
B.2 Battery compartment
B.2.1 General
30 B.2.2 Limiting access by children
B.3 Voltage cut-off
31 Annex C (normative) Designation system (nomenclature)
C.1 General
C.2 Designation system in use up to October 1990
C.2.1 General
C.2.2 Cells
32 Table C.1 – Physical designation and dimensions of round cells and batteries
33 C.2.3 Electrochemical system
C.2.4 Batteries
Table C.2 – Physical designation and nominal overall dimensions of flat cells
Table C.3 – Physical designation and dimensions of square cells and batteries
34 C.2.5 Modifiers
C.2.6 Examples
C.3 Designation system in use since October 1990
C.3.1 General
C.3.2 Round batteries
35 Figures
Figure C.1 – Designation system for round batteries: d1 < 100 mm; height h1 < 100 mm
36 Figure C.2 – Diameter code for non-recommended diameters
Table C.4 – Diameter code for recommended diameter
37 Figure C.3 – Height code for denoting the hundredths of a millimetre of height
38 C.3.3 Non-round batteries
Figure C.4 – Designation system for round batteries: d1 ≥ 100 mm; height h1 ≥ 100 mm
39 Figure C.5 – Designation system for non-round batteries, dimensions < 100 mm
40 Figure C.6 – Designation system for non-round batteries, dimensions ≥ 100 mm
Figure C.7 – Height code for discrimination per tenth of a millimetre
41 C.3.4 Ambiguity
Table C.5 – Physical designation and dimensions of round cellsand batteries based on Clause C.2
42 Table C.6 – Physical designation and dimensions of non-round batteries based on Clause C.2
43 Annex D (informative) Standard discharge voltage Us – Definition and method of determination
D.1 Definition
D.2 Determination
D.2.1 General considerations: the C/R-plot
44 D.2.2 Determination of the standard discharge resistor Rs
Figure D.1 – Normalized C/R-plot (schematic)
45 D.2.3 Determination of the standard discharge capacity Cs and standard discharge time ts
Figure D.2 – Standard discharge voltage (schematic)
46 D.3 Experimental conditions to be observed and test results
Table D.1 – Standard discharge voltage by system
47 Annex E (informative) Preparation of standard methods of measuring performance (SMMP) of consumer goods
E.1 General
E.2 Performance characteristics
E.3 Criteria for the development of test methods
48 Annex F (informative) Guidance for proposing value of minimum average duration
F.1 General
F.2 Sampling
F.3 Calculation method
49 Annex G (normative) Code of practice for packaging, shipment, storage, use and disposal of primary batteries
G.1 General
G.2 Packaging
G.3 Transport and handling
G.4 Storage and stock rotation
50 G.5 Displays at sales points
G.6 Selection, use and disposal
G.6.1 Purchase
G.6.2 Installation
G.6.3 Use
51 G.6.4 Replacement
G.6.5 Disposal
52 Annex H (informative) Compliance checklist
53 Bibliography

Related products

BS EN IEC 60086-1:2021
$198.66