BS EN 61169-53:2016
$142.49
Radio-frequency connectors – Sectional specification for RF coaxial connectors with inner diameter of outer conductor 16 mm with screw lock. Characteristic impedance 50 O (Type S7-16)
| Published By | Publication Date | Number of Pages |
| BSI | 2016 | 28 |
This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with threaded coupling, typically for use in 50 Ω cable networks (Type S7-16).
It prescribes mating face dimensions for general purpose connectors – grade 2, dimensional details of standard test connectors-grade 0, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series 4.1-9.5 RF connectors.
This specification indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.
The S7-16 series RF coaxial connectors with nominal impedance 50 Ω are threaded coupling units which are used with all kinds of RF cables and microstrips in microwave transmission system. And the working frequency is up to 7,5 GHz.
NOTE Metric dimension are original dimensions. All undimensioned pictorial configurations are for reference purpose only.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | English CONTENTS |
| 8 | FOREWORD |
| 10 | 1 Scope 2 Normative references 3 Mating face and gauge information 3.1 Dimensions – General connectors – Grade 2 3.1.1 Connector with pin-centre contact |
| 11 | 3.1.2 Connector with socket centre contact Figures Figure 1 – Connector with pin-centre contact (for dimensions, see Table 1) Tables Table 1 – Dimensions of connector with pin-centre contact |
| 12 | 3.2 Gauges 3.2.1 Gauge pin for socket-centre contact Figure 2 – Connector with socket-centre contact (for dimensions, see Table 2) Table 2 – Dimensions of connector with socket centre contact |
| 13 | 3.2.2 Test procedure 3.3 Dimensions – Standard test connectors – Grade 0 3.3.1 Connector with pin-centre contact Figure 3 – Gauge pin for socket-centre contact (for dimensions, see Table 3) Table 3 – Dimensions of gauge pin for socket-centre contact |
| 14 | 3.3.2 Standard test connector with socket-centre contact Figure 4 – Connector with pin-centre contact (for dimensions, see Table 4) Table 4 – Dimensions of connector with pin-centre contact |
| 15 | Figure 5 – Connector with socket-centre contact (for dimensions, see Table 5) Table 5 – Dimensions of connector with socket-centre contact |
| 16 | 4 Quality assessment procedures 4.1 General 4.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013) Table 6 – Rating and characteristics |
| 18 | 4.3 Test schedule and inspection requirements 4.3.1 Acceptance tests 4.3.2 Periodic tests Table 7 – Acceptance tests |
| 19 | 4.4 Procedures for the quality conformance 4.4.1 Quality conformance inspection Table 8 – Periodic tests |
| 20 | 4.4.2 Qualification approval and its maintenance 5 Instructions for preparation of detail specifications 5.1 General 5.2 Identification of the component 5.3 Performances 5.4 Marking, ordering information and related matters 5.5 Selection of tests, test conditions and severities |
| 21 | 5.6 Blank detail specification pro-forma for type S7-16 connector |
| 25 | 6 Marking 6.1 Marking of component 6.2 Marking and contents of package |
