🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 1643:2022 – TC

BS EN 1643:2022 – TC

$226.20

Tracked Changes. Safety and control devices for burners and appliances burning gaseous and/or liquid fuels. Valve proving systems for automatic shut-off valves

Published By Publication Date Number of Pages
BSI 2022 114
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

EN 13611:2019, Clause 1 is replaced by following: This document specifies the safety, design, construction and performance requirements, and testing for valve-proving systems, hereafter referred to as “VPS”, intended for use with gas burners and gas-burning appliances burning one or more gaseous fuels. This document applies to all types of VPS used for the automatic detection of leakage in a gas burner section having at least two automatic shut-off valves, and which give a signal if the leakage of one of the valves, the piping in-between the valves or of the VPS itself and its components exceeds the detection limit. This document applies to VPS for gases with a maximum inlet pressure up to and including 500 kPa. This document does not apply to VPSs for use in explosive atmospheres. This document is applicable to AC and DC supplied VPS (for VPS supplied by stand-alone battery system, battery systems for mobile applications, or VPS which are intended to be connected to DC supply networks, see Annex I).

PDF Catalog

PDF Pages PDF Title
1 30466129
65 A-30421823
66 undefined
74 1 Scope
2 Normative references
75 3 Terms and definitions
77 4 Classification
5 Test conditions and uncertainty of measurements
6 Design and construction
81 7 Performance
86 8 Electrical requirements
9 Electromagnetic compatibility (EMC)
90 10 Marking, instructions
91 Annex A (informative)Abbreviations and Symbols
92 Annex B (informative)Leak-tightness tests for gas controls − volumetric method
93 Annex C (informative)Leak-tightness tests for gas controls − pressure loss method
94 Annex D (normative)Calculation of pressure loss into leakage rate
95 Annex E (normative)Electrical/electronic component fault modes
97 Annex F (normative)Additional requirements for safety accessories and pressure accessories as defined in EU Directive 2014/68/EU
98 Annex G (normative)Materials for pressurized parts
99 Annex H (normative)Additional materials for pressurized parts
100 Annex I (normative)Requirements for controls used in DC supplied burners and appliances burning gaseous or liquid fuels
I.1 Introduction
102 Annex J (normative)Method for the determination of a Safety Integrity Level (SIL)
103 Annex K (normative)Method for the determination of a Performance Level (PL)
104 Annex L (informative)Relationship between Safety Integrity Level (SIL) and Performance Level (PL)
105 Annex M (normative)Reset functions
106 Annex N (informative)Guidance document on Environmental Aspects
107 Annex O (normative)Seals of elastomer, cork and synthetic fibre mixtures
108 Annex AA (informative)Application Guidance
AA.1 General
AA.2 Use of a VPS
109 Annex ZA (informative)Relationship between this document and the essential requirements of Directive 2009/142/EC aimed to be covered
110 Annex ZB (informative)Relationship between this European Standard and the essential requirements of Regulation (EU) 2016/426 aimed to be covered
111 Annex ZC (informative)Relationship between this document and the essential requirements of Directive 2014/68/EU aimed to be covered

Related products

BS EN 1643:2022 - TC
$226.20