BS 4HR 100:2010+A1:2012
$198.66
Aerospace series. Procedure for inspection, testing and acceptance of wrought heat-resisting alloys
| Published By | Publication Date | Number of Pages |
| BSI | 2012 | 68 |
This British Standard specifies procedures for inspection, testing and acceptance of wrought heat-resisting alloys for aerospace purposes.
The standard is applicable to material specifications in the British Standard Aerospace HR series and also to other British Standard material specifications for wrought heat-resisting alloys which are suitable for aerospace use.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 7 | Foreword |
| 11 | Section 1: General requirements 1 Scope 2 Normative references |
| 12 | 3 Terms and definitions |
| 14 | 4 General |
| 15 | 5 Information and requirements to be agreed and documented |
| 18 | 6 Manufacture and freedom from defects |
| 19 | 7 Preparation for inspection 8 Heat treatment |
| 20 | 9 Chemical composition 10 Testing |
| 23 | 11 Maintenance of identity 12 Marking |
| 24 | 13 Protection and packaging 14 Certification |
| 26 | Section 2: Bars for machining and sections 15 General 16 Dimensions and tolerances 17 Tensile, creep and stress-rupture tests |
| 27 | 18 Hardness test 19 Internal defects |
| 28 | 20 External defects 21 Macroexamination Table 1 Number of bars or sections to be sampled |
| 29 | 22 Marking |
| 30 | Section 3: Forging stock and billets and bars for subsequent working 23 General 24 Dimensions and tolerances 25 Tensile, creep and stress-rupture tests Table 2 �Minimum reduced diameter, section or thickness of side forged test samples for billets, bars and sections |
| 31 | 26 Internal defects 27 External defects 28 Macroexamination |
| 32 | 29 Marking |
| 33 | Section 4: Forgings 30 General 31 Manufacture 32 Pre-production forgings |
| 34 | 33 Production forgings 34 Procedure X for process control testing |
| 35 | 35 Forgings subject to heat treatment after delivery 36 Selection and preparation of mechanical test samples for batch release testing Table 3 Maximum number of forgings to be manufactured between the collection of test samples |
| 36 | Table 4 Minimum reduced diameter, section or thickness of side forged test samples for forging stock |
| 37 | Table 5 Tensile, creep and stress-rupture property requirements for forgings |
| 38 | 37 Hardness test 38 Internal defects |
| 39 | 39 External defects 40 Grain flow and grain size 41 Marking |
| 40 | Section 5: Plate, sheet and strip 42 General 43 Dimensions and tolerances 44 Tensile, creep and stress-rupture tests Table 6 Tolerances for plate, sheet and strip Table 7 Position of the test sample axis within the plate, sheet or strip |
| 41 | 45 Hardness test |
| 42 | 46 Single bend test 47 External defects 48 Marking |
| 44 | Section 6: Tubes 49 General 50 Dimensions and tolerances 51 Tensile, creep and stress-rupture tests |
| 45 | 52 Hardness test 53 Drifting test |
| 46 | 54 Distension test 55 Flattening test |
| 47 | 56 Pressure test 57 External defects |
| 48 | 58 Marking |
| 49 | Section 7: Wire 59 General 60 Dimensions and tolerances 61 Tensile, creep and stress-rupture tests |
| 50 | 62 Ductility tests |
| 51 | 63 External defects 64 Macroexamination |
| 52 | 65 Marking |
| 53 | Section 8: Parts finally heat treated after machining 66 General 67 Manufacture 68 Condition 69 Heat treatment 70 Mechanical tests |
| 54 | 71 Hardness test 72 External defects |
| 55 | Section 9: Bar and wire intended for the manufacture of fasteners 73 General 74 Dimensions and tolerances 75 Hardness test |
| 56 | 76 Macroexamination 77 Grain size determination |
| 57 | 78 Surface contamination |
| 58 | Annex A (normative) Rules for application of values for chemical composition and mechanical properties given in material specifications Annex B (normative) Dimensional tolerances Table B.1 Tolerances on diameters of drawn and ground bars All dimensions are in millimetres |
| 59 | Table B.2 Tolerances on widths across flats of bright drawn bars All dimensions are in millimetres Table B.3 Tolerances on diameters of machined round bars All dimensions are in millimetres Table B.4 Tolerances on thicknesses of cold rolled plate and sheet All dimensions are in millimetres Table B.5 Tolerances on thicknesses of hot rolled plate and sheet All dimensions are in millimetres |
| 60 | Table B.6 Tolerances on thicknesses of cold rolled strip All dimensions are in millimetres Table B.7 �Tolerances on widths and lengths of cold rolled plate and sheet All dimensions are in millimetres Table B.8 Tolerances on widths and lengths of hot rolled plate and sheet All dimensions are in millimetres Table B.9 Tolerances on widths of cold rolled strip All dimensions are in millimetres |
| 62 | Table B.10 �Tolerances on dimensions of cold worked tubes All dimensions are in millimetres. See B.1. |
| 64 | Table B.11 Tolerances on diameters of wire All dimensions are in millimetres |
| 65 | Bibliography |
