AGMA 93FTM08:1993 Edition
$14.30
Single Flank Testing and Structure-Born Noise Analysis
Published By | Publication Date | Number of Pages |
AGMA | 1993 | 13 |
If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]
Proposes that testing the running behavior of an installation-ready gearset must take place on bevel and hypoid gear testers. Describes single flank generation testing and structure-borne noise analysis of gear pairs, based on a highly modern real•time analysis device for which software was specially developed for the transmission testing of gearsets. Explains the new possibilities and offers a trouble shooting example.
Published Code | AGMA |
---|---|
Published By | American Gear Manufacturers Association |
Publication Date | 1993 |
Pages Count | 13 |
Language | English |
File Size | 839.7 KB |
Related products
-
AGMA 96FTM04:1996 Edition
Traceable Calibration of Master Gears at PTB Published By Publication Date Number of Pages AGMA…
-
AGMA 99FTM02:1999 Edition
Traceability Strategies for the Calibration of Spline and Serration Gauges Published By Publication Date Number…
-
AGMA 90FTM08:1990 Edition
Investigations on the Scuffing Resistance of High-Speed Gears Published By Publication Date Number of Pages…
-
AGMA 96FTM08:1996 Edition
Thermal Rating of Gear Drives Balance Between Power Loss and Heat Dissipation Published By Publication…
-
AGMA 99FTM08:1999 Edition
Power-Dry-Cutting of Bevel Gears Published By Publication Date Number of Pages AGMA 1999 13
-
AGMA 90FTM03:1990 Edition
Simulation of Meshing, Transmission errors and Bearing Contact for Single-Enveloping Worm-Gear Drives Published By Publication…
-
AGMA 90FTM06:1990 Edition
Dynamic Responses of Aircraft Gears Published By Publication Date Number of Pages AGMA 1990 21
-
AGMA 91FTM07:1991 Edition
Low Cycle and Static Bending Strength of Carburized and High Hardness Through Hardened Gear Teeth…
-
AGMA 91FTM06:1991 Edition
Comparing Surface Failure Modes in Bearings and Gears: Appearances versus Mechanisms Published By Publication Date…
-
AGMA 99FTM07:1999 Edition
Ductile Iron as a Material for Open Gearing Published By Publication Date Number of Pages…
-
AGMA 13FTM08:2013 Edition
Application and Improvement of Face Load Factor Determination Based on AGMA 927 (Accurate and Fast…
-
AGMA 91FTM08:1991 Edition
Methods of Statistical Dynamics for the Calculation of Gear Stress Distribution and its Effect on…
-
AGMA 93FTM13:1993 Edition
CAGE – Computer Aided Engineering Software Published By Publication Date Number of Pages AGMA 1993…
-
AGMA 93FTM06:1993 Edition
Effect of Radial Runout on Element Measurements Published By Publication Date Number of Pages AGMA…
-
AGMA 98FTM03:1998 Edition
Basic Studies on Fatigue Strength of Case-Hardened Gear Steel – Effects of Shot Peening and/or…
-
AGMA 99FTM04:1999 Edition
Gear Oil Micropitting Evaluation Published By Publication Date Number of Pages AGMA 1999 18
-
AGMA 94FTM01:1994 Edition
Fatigue Analysis of Shafts for Marine Gearboxes Published By Publication Date Number of Pages AGMA…
-
AGMA 93FTM03:1993 Edition
A Rayleigh-Ritz Approach to Determine Compliance and Root Stresses in Spiral Bevel Gears Using Shell…
-
AGMA 93FTM01:1993 Edition
Undercutting in Worms and Worm-Gears Published By Publication Date Number of Pages AGMA 1993 12
-
AGMA 04FTM08:2004 Edition
Generalized Excitation of Traveling Wave Vibration in Gears Published By Publication Date Number of Pages…
-
AGMA 93FTM09:1993 Edition
Gear Tooth Bending Fatigue Crack Detection by Acoustic Emissions and Tooth Compliance Measurements Published By…
-
AGMA 05FTM08:2005 Edition
New Developments in Tooth Contact Analysis (TCA) and Loaded TCA for Spiral Bevel and Hypoid…
-
AGMA 93FTM04:1993 Edition
Stress Analysis of Spiral Bevel Gear: A Novel Approach to Tooth Modelling Published By Publication…
-
AGMA 95FTM08:1995 Edition
Miner’s Rule a More Definitive Approach Published By Publication Date Number of Pages AGMA 1995…
-
AGMA 98FTM05:1998 Edition
Low Vibration Design on a Helical Gear Pair Published By Publication Date Number of Pages…
-
AGMA 92FTM08:1992 Edition
The Role of Reliability for Bearings and Gears Published By Publication Date Number of Pages…
-
AGMA 98FTM08:1998 Edition
New Test Methods for the Evaluation of Wear, Scuffing and Pitting Capacity of Gear Lubricants…
-
AGMA 99FTM01:1999 Edition
The Barkhausen Noise Inspection Method for Detecting Grinding Damage in Gears Published By Publication Date…
-
AGMA 97FTM08:1997 Edition
New Guidelines for Wind Turbine Gearboxes Published By Publication Date Number of Pages AGMA 1997…
-
AGMA 10FTM08:2010 Edition
Calculation of Load Distribution in Planetary Gears for an Effective Gear Design Process Published By…
-
AGMA 93FTM02:1993 Edition
Topological Tolerancing of Worm-Gear Tooth Surfaces Published By Publication Date Number of Pages AGMA 1993…
-
AGMA 96FTM03:1996 Edition
Noise Reduction Through Generated Engagement Relief Modification Published By Publication Date Number of Pages AGMA…
-
AGMA 99FTM18:1999 Edition
Effects of Wear on the Meshing Contact of Worm Gearing Published By Publication Date Number…
-
AGMA 93FTM07:1993 Edition
New Developments in Design, Manufacturing and Applications of Cylkro- (Face) Gears Published By Publication Date…
-
AGMA 92FTM06:1992 Edition
Comparison of Carburized Gear Materials in Pitting Published By Publication Date Number of Pages AGMA…
-
AGMA 94FTM08:1994 Edition
Reference Point, Mesh Stiffness and Dynamic Behavior of Solid, Semi-Solid and Thin-Rimmed Spur Gears Published…
-
AGMA 98FTM06:1998 Edition
Calibration of Master Gears on Coordinate Measurement Machines Published By Publication Date Number of Pages…
-
AGMA 91FTM09:1991 Edition
Rerating Damaged Naval Ship Propulsion Gear Published By Publication Date Number of Pages AGMA 1991…
-
AGMA 93FTM05:1993 Edition
Optimal Gear Design for Equal Strength Teeth Using Addendum Modification Coefficients Published By Publication Date…
-
AGMA 97FTM01:1997 Edition
Calibration of Gear Measuring Instruments and their Application to the Inspection of Product Gears Published…