AGMA 07FTM18:2007 Edition
$14.30
Bevel Gear Model
Published By | Publication Date | Number of Pages |
AGMA | 2007 | 12 |
If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]
The paper presents a method for developing an accurate generic bevel gear model including both the face milling and face hobbing processes. Starting with gear blank geometry, gear and pinion basic generator machine settings are calculated. The contact pattern and rolling quality are specified and held to the second order in terms of pattern length, contact bias and motion error. Based on the setup, a grid of tooth points are found including the tooth flank, fillet and, if it exists, the undercut area. It is proposed as the model for the next generation of bevel gear strength calculations in that the procedure produces true bevel gear geometry, uses blank design parameters as input and is vendor independent except for cutter diameter.
Published Code | AGMA |
---|---|
Published By | American Gear Manufacturers Association |
Publication Date | 2007 |
Pages Count | 12 |
Language | English |
File Size | 399.4 KB |
Related products
-
AGMA 09FTM18:2009 Edition
Does the Type of Gear Action Affect the Appearance of Micro-Pitting and Gear Life? Published…
-
AGMA 05FTM15:2005 Edition
Repair of Helicopter Gears Published By Publication Date Number of Pages AGMA 2005 11
-
AGMA 08FTM18:2008 Edition
Gear Corrosion During the Manufacturing Process Published By Publication Date Number of Pages AGMA 2008…
-
AGMA 12FTM18:2012 Edition
Analysis of Ripple on Noisy Gears Published By Publication Date Number of Pages AGMA 2012…
-
AGMA 09FTM08:2009 Edition
Load Sharing Analysis of High Contact Ratio Spur Gears in Military Tracked Vehicle Application Published…
-
AGMA 07FTM12:2007 Edition
The Effect of Start-Up Load Conditions on Gearbox Performance and Life – Failure Analysis and…
-
AGMA 04FTM08:2004 Edition
Generalized Excitation of Traveling Wave Vibration in Gears Published By Publication Date Number of Pages…
-
AGMA 01FTM11:2001 Edition
Separation of Sliding and Rolling Between Meshing Profiles Published By Publication Date Number of Pages…
-
AGMA 97FTM13:1997 Edition
Three Innovations Advance the Science of Shot Peening Published By Publication Date Number of Pages…
-
AGMA 06FTM13:2006 Edition
Economic Aspects of Vacuum Carburizing Published By Publication Date Number of Pages AGMA 2006 8
-
AGMA 09FTM13:2009 Edition
Bending Fatigue, Impact Strength and Pitting Resistance of Ausformed Powder Metal Gears Published By Publication…
-
AGMA 97FTM12:1997 Edition
Introduction of a Jobbing System for Bevel and Hypoid Gears Published By Publication Date Number…
-
AGMA 08FTM14:2008 Edition
Effects of Axle Deflection and Tooth Flank Modification on Hypoid Gear Stress Distribution and Contact…
-
AGMA 07FTM15:2007 Edition
Experience with a Disc Rig Micropitting Test Published By Publication Date Number of Pages AGMA…
-
AGMA 99FTM18:1999 Edition
Effects of Wear on the Meshing Contact of Worm Gearing Published By Publication Date Number…
-
AGMA 06FTM15:2006 Edition
Optimal Tooth Modifications in Spiral Bevel Gears Introduced by Machine Tool Setting Variation Published By…
-
AGMA 05FTM08:2005 Edition
New Developments in Tooth Contact Analysis (TCA) and Loaded TCA for Spiral Bevel and Hypoid…
-
AGMA 07FTM11:2007 Edition
Helicopter Accessory Gear Failure Analysis Involving Wear and Bending Fatigue Published By Publication Date Number…
-
AGMA 06FTM16:2006 Edition
Certificate for Involute Gear Evaluation Software Published By Publication Date Number of Pages AGMA 2006…
-
AGMA 05FTM14:2005 Edition
Determining the Shaper Cut Helical Gear Fillet Profile Published By Publication Date Number of Pages…
-
AGMA 07FTM01:2007 Edition
Estimation of Lifetime of Plastic Gears Published By Publication Date Number of Pages AGMA 2007…
-
AGMA 08FTM16:2008 Edition
Hob Tool Life Technology Update Published By Publication Date Number of Pages AGMA 2008 15
-
AGMA 07FTM19:2007 Edition
How to Determine the MTBF of Gearboxes Published By Publication Date Number of Pages AGMA…
-
AGMA 01FTM10:2001 Edition
Design Technologies of High-Speed Gear Transmission Published By Publication Date Number of Pages AGMA 2001…
-
AGMA 07FTM13:2007 Edition
Influence of Grinding Burn on the Load Carrying Capacity of Parts under Rolling Stress Published…
-
AGMA 07FTM14:2007 Edition
Roughness and Lubricant Chemistry Effects in Micropitting Published By Publication Date Number of Pages AGMA…
-
AGMA 05FTM10:2005 Edition
Finite Element Study of the Ikona Gear Tooth Profile Published By Publication Date Number of…
-
AGMA 07FTM17:2007 Edition
Simulation Model for the Emulation of the Dynamic Behavior of Bevel Gears Published By Publication…
-
AGMA 07FTM08:2007 Edition
Manufacturing Net Shaped Cold Formed Gears Published By Publication Date Number of Pages AGMA 2007…
-
AGMA 97FTM08:1997 Edition
New Guidelines for Wind Turbine Gearboxes Published By Publication Date Number of Pages AGMA 1997…
-
AGMA 07FTM10:2007 Edition
The Gear Dynamic Factor, Historical and Modern Perspective Published By Publication Date Number of Pages…
-
AGMA 09FTM17:2009 Edition
Variation Analysis of Tooth Engagement and Load-Sharing in Involute Splines Published By Publication Date Number…
-
AGMA 05FTM17:2005 Edition
Influences of Bearing Life Considerations on Gear Drive Design Published By Publication Date Number of…
-
AGMA 09FTM15:2009 Edition
High Performance Industrial Gear Lubricants for Optimal Reliability Published By Publication Date Number of Pages…
-
AGMA 14FTM18:2014 Edition
Precision Bevel Gears with Low Tooth Count Published By Publication Date Number of Pages AGMA…
-
AGMA 06FTM10:2006 Edition
Fabrication, Assembly and Test of a High Ratio, Ultra Safe, High Contact Ratio, Double Helical…
-
AGMA 08FTM08:2008 Edition
PM Materials for Gear Applications Published By Publication Date Number of Pages AGMA 2008 9
-
AGMA 06FTM14:2006 Edition
The Optimal High-Speed Cutting of Bevel Gears – New Tools and New Cutting Parameters Published…
-
AGMA 07FTM16:2007 Edition
Straight Bevel Gear Cutting and Grinding on CNC Free Form Machines Published By Publication Date…
-
AGMA 09FTM19:2009 Edition
The Effect of Gearbox Architecture on Wind Turbine Enclosure Size Published By Publication Date Number…