1.1 Part A-General Test Methods for Evaluating the Basic Properties of Wood-Base Fiber and Particle Panel Materials These test methods cover the determination of the properties of wood-base fiber and particle panel materials that are produced as mat-formed panels such as particleboard, medium-density fiberboard and hardboard. Some of the test methods are applicable to other panel products such as oriented strand board. The test methods are as follows:<\/p>\n
1.3 There are accepted basic test procedures for various fundamental properties of materials that may be used without modification for evaluating certain properties of wood-based fiber and particle panel materials. These test methods are included elsewhere in the Annual Book of ASTM Standards. The pertinent ones are listed in . A few of the test methods referenced are for construction where the wood-base materials often are used.<\/p>\n
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents are approximate in many cases. 1 in. = 25.4 mm, 1 lbf = 4.45 N.<\/p>\n
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 1<\/td>\n | Scope <\/td>\n<\/tr>\n | ||||||
| 2<\/td>\n | Referenced Documents Significance and Use Apparatus TABLE 1 <\/td>\n<\/tr>\n | ||||||
| 3<\/td>\n | Test Specimens Moisture Content and Conditioning Requirements Accelerated Aging <\/td>\n<\/tr>\n | ||||||
| 4<\/td>\n | FIG. 1 <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | Size, Physical Properties and Appearance of Panels Static Bending FIG. 2 FIG. 3 <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | FIG. 4 <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Tension Parallel to Surface FIG. 5 <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | FIG. 6 FIG. 7 <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | Tension Perpendicular to Surface (Internal Bond) Compression Parallel to Surface <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | FIG. 8 FIG. 9 <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | Lateral Nail Resistance FIG. 10 <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | Nail Withdrawal Nail-Head Pull-Through FIG. 11 <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | FIG. 12 FIG. 13 FIG. 14 <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | Direct Screw Withdrawal Hardness <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | Hardness Modulus Shear in the Plane of the Panel FIG. 15 <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | FIG. 16 <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | FIG. 17 <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | Glue-Line Shear (Block Type) FIG. 18 FIG. 19 <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | Falling Ball Impact FIG. 20 FIG. 21 <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | Abrasion Resistance by the U.S. Navy Wear Tester Water Absorption and Thickness Swelling FIG. 22 FIG. 23 <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | Linear Expansion with Change in Moisture Content <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | Cupping and Twisting Interlaminar Shear FIG. 24 <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | FIG. 25 FIG. 26 FIG. 27 <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | Edgewise Shear FIG. 28 <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | Compression-Shear FIG. 29 FIG. 30 <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | FIG. 31 <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | FIG. 32 TABLE 2 <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | Test Panel Test Specimens Conditioning Thickness Modulus of Rupture FIG. 33 <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | Tension Parallel to Surface Tension Perpendicular to Surface FIG. 34 <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | Water Absorption and Thickness Swelling Moisture Content and Specific Gravity Report Precision and Bias Keywords <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" D1037-06a Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials<\/b><\/p>\n |