AS 4596:1999
$16.25
Copper, lead and zinc sulfide concentrates – Determination of mass of contained metal in a lot
| Published By | Publication Date | Number of Pages |
| AS | 1999-08-05 | 14 |
Specifies a method for determining the mass of contained metal in a lot, based on the wet mass, moisture content and dry basis metal content of the lot. This Standard is identical with and has been reproduced from ISO 13543:1996.
Scope
This International Standard specifies the method for determining the mass of contained metal in a lot, based on the wet mass, moisture content and dry basis metal content of the lot. The procedure for estimating the variance and confidence intervals for the mass of contained metal is also specified.
Related products
-
ISO 4592:1992
Plastics — Film and sheeting — Determination of length and width Published By Publication Date…
-
AS/NZS 4536:1999 (R2014)
Life cycle costing – An application guide Published By Publication Date Number of Pages AS…
-
SAE AIR 4096:1989
Helicopter Engine Foreign Object Damage Published By Publication Date Number of Pages SAE 1989-11-30 8
-
AS/NZS 4096:1993
Information technology – Open Systems Interconnection – Connectionless ACSE protocol specification Published By Publication Date…
-
ASTM-D596 1995
D596-91(1995) Standard Guide for Reporting Results of Analysis of Water Published By Publication Date Number…
-
AS 4597:1999 (R2015)
Installation of roof slates and shingles (Non-interlocking type) Published By Publication Date Number of Pages…
-
AS/NZS 4576:1995
Guidelines for scaffolding Published By Publication Date Number of Pages AS 1995-06-14 147
-
SAE MA 4569:1994
Hose Assembly, PTFE, Aramid Reinforced, Standard Duty, 21000/28000 kPa, 135 °C, Titanium Fittings, Flareless, Including…
-
AS/NZS 4506:1998
Metal finishing – Thermoset powder coatings Published By Publication Date Number of Pages AS 1998…
-
ISO 4896:1990
Plastics — Melamine/phenolic moulding materials — Specification Published By Publication Date Number of Pages ISO…
-
AS/NZS 4526:1998
Abrasive belts – Selection of width/length combinations Published By Publication Date Number of Pages AS…
-
AS 3596:1992
Energy management programs – Guidelines for definition and analysis of energy and cost savings Published…
-
BS 6596:1992
Specification for ratios of proof and burst pressure to design working pressure for rubber and…
-
ISO 4566:1992
Small craft with inboard engine — Propeller shaft ends and bosses with 1:10 taper Published…
-
ASTM-D4596 1993
D4596-93 Standard Practice for Collection of Channel Samples of Coal in a Mine Published By…
-
ISO 4591:1992
Plastics — Film and sheeting — Determination of average thickness of a sample, and average…
-
BS 4586:1992
Specification for spiral wire reinforced rubber covered hydraulic hoses and hose assemblies Published By Publication…
-
BS 4196-8:1991
Sound power levels of noise sources – Specification for the performance and calibration of reference…
-
AS/NZS 2596:1995
Seat belt assemblies for motor vehicles Published By Publication Date Number of Pages AS 1995-09-05…
-
ISO 4506:1979
Hardmetals — Compression test Published By Publication Date Number of Pages ISO 1979-10 6
-
BS 4592-4:1992:2003 Edition
Industrial type flooring, walkways and stair treads – Specification for glass reinforced plastics open bar…
-
ISO 5596:1999
Hydraulic fluid power — Gas-loaded accumulators with separator — Ranges of pressures and volumes and…
-
ASTM-B596 1999
B596-89(1999) Standard Specification for Gold-Copper Alloy Electrical Contact Material Published By Publication Date Number of…
-
API PUBL 4546-1992
Ecological Effects of Produced Water Discharges from Offshore Oil and Gas Production Platforms Published By…
-
BS 1596:1992
Specification for fibreboard drums Published By Publication Date Number of Pages BSI 1992 12
-
API PUBL 4566-1992
Evaluation of the Technology Alternatives for Controlling Fugitive Emissions from Sludge Dewatering Operations Published By…
-
AS/NZS 1596:1997
Storage and handling of LP Gas Published By Publication Date Number of Pages AS 1997-09-05…
-
AS/NZS 4196:1999 (R2013)
Information and documentation – Open Systems Interconnection – Interlibrary loan application service definition Published By…
-
ASTM-C596 1996
C596-96e1 Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement Published By Publication…
-
AS/NZS 4516:1998
Abrasive products – Diamond or cubic boron nitride grinding wheels – Dimensions Published By Publication…
-
IEEE 1596 1992:2001 Edition
IEEE Standard for Scalable Coherent Interface (SCI) Published By Publication Date Number of Pages IEEE…
-
IEEE 1596-1992
IEEE Standard for Scalable Coherent Interface (SCI) Published By Publication Date Number of Pages IEEE…
-
AS/NZS 4396:1999 (R2016)
Connectors – Insulation piercing – For 0.6/1 kV aerial bundled cables Published By Publication Date…
-
SAE AS 4546:1992
Hose, Air Duct, Flexible, Silicone-Coated Fabric, 1 to -.5 psi, External Nylon Helix, Self-Extinguishing Published…
-
AS/NZS 4496:1997 (R2016)
Recommended practice for the colour coding of steel products Published By Publication Date Number of…
-
BS 4591:1990
Method for determination of distillation characteristics of organic liquids (other than petroleum products) Published By…
-
ISO 4576:1996
Plastics — Polymer dispersions — Determination of sieve residue (gross particle and coagulum content) Published…
-
ISO 4593:1993
Plastics — Film and sheeting — Determination of thickness by mechanical scanning Published By Publication…
-
JIS C 4506:1995
Small Switches for Single-phase Motors Published By Publication Date Number of Pages JIS 1995-03 11
-
ISO 4546:1993
Metallic materials — Hardness test — Verification of Knoop hardness testing machines Published By Publication…
